9005+9006+H11 LED HEADLIGHT BULBS CONVERSION KIT Replace High Beam+Low Beam+Fog Light 50w/set, 8000lm/set, CSP led chips. CSP LED headlights: Imported CSP chips, high optical density & low heat resistance, enhance light efficiency up to 95%. -Fan-less design: Advanced heat conduction system+unique grooved heat sink fins keep the light bulb in appropriate working temperature, No noise caused by fan.-Error_free, Zrro warm-up: Work with most vehicle's computer system without error. Light uo your road instantly without warming up. -Rain-Resistant: Better works on rainy days and even in the harsh conditions.
Available Single Beam Bulb size: 9005;9006;H11 (Replace high beam or low beam or fog light). Power: 50W/set(25W/bulb) LED Quantity: 6Pcs / 12Pcs CSP LED Chips (each bulb) Luminous Flux: approx. 6pcs LED Headlight Bulbs English User Manual. Notice 1: All led bulbs have heat sink, please make sure there is enough space behind the headlight housing (about 45mm) for the heat sink of led headlight. Notice 2: (1)These led headlight bulbs kit only replace Factory Halogen bulbs, they won't replace Factory HID bulbs.
(2)9005/HB3 led bulbs also can replace Fog Light 9145 9140 H10, but before replacing, will need to do a little modification on the retainer holder of led bulbs, then can twist to lock the bulb into place. (3)9006/HB4 led bulbs also can replace single beam 9012. (4)This LED bulb 880/H1 is NOT fully plug & play for some vehicles, some modification may be needed, need connect them to factory positive and negative to get power.Will these led bulbs fit for my car? (1)Go to "sylvania-automotive" website, find the part number of stock bulb on your vehicle. (2)Take a look in your vehicle handbook or Take out your existing bulb from your vehicle, verify the part number of the bulb, match the part number on our listing. Q2:How to install these led bulbs and get good pattern? A:Should be installed vertical, and the diodes are at 9 and 3 o'clock position.
(about 9007/H4/H13 hi-lo beam led bulbs, the high beam is at the bottom, the low beam is at the top) Each car's headlamp reflector is different , so for some vehicle, 9004/9007/H4/H13 led bulbs will need adjust the angle to get the good pattern. First let the headlight shines toward the wall, remove the screws from the bracket and install the led bulbs into the headlight housing and turn the bulb slowly to find the best pattern, then twist back the screws of LED bulb's bracket to fix. Sometimes after finding the best angle, maybe you will need to drill a new hole manually to fix.Q3:After installing, why neither side led bulbs turn on or lighting up? Or both sides led bulbs are flickering? Or have error code on car computer?
A: (1)First, Polarity Problem. Unlike halogen bulbs, LED are polarity sensitive. Different car manufactures have different polarity setup, if led bullbs don't turn on or lighting up, Pls check for a polarity mismatch, disconnect the bulb and flip the socket in order to reverse the polarity to install.(2)Second, Compatible Problem(Voltage Problem). The vehicle's computer system is sensitive to the led headlight bulb (the power of the led headlight bulb is lower than the halogen ones). Therefore, it may be occur compatible problem (flickering, error code, radio interference, headlamp fog light interference, high beam and low beam interference, etc) , after replacing the led headlight on some vehicle, e. Audi, Mercedes, Ford, Volkswagen, Volvo, Jeep Dodge and Ram etc, then will need to add resistor/decoders to solve these compatible problems. The item "BEAMTECH H11+9005+9006 LED Headlight Bulbs High Beam+Low Beam+Fog Light Replace" is in sale since Wednesday, June 19, 2019. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Lighting & Lamps\Light Bulbs\LED Lights". The seller is "mzs-us" and is located in Sacramento, California. This item can be shipped to United States, Canada.